Ultrasonic cleaning machine is a highly precise cleaning scientific equipment. In our daily use, it is normal to have some small exceptions with small probability. In addition to daily equipment maintenance, pay attention to the use mode, operation process or environmental location. If the usage is improper or the internal and external environment changes seriously, the usage may be asymmetric. What are the common abnormalities and countermeasures of ultrasonic cleaning machine? Let's talk about it.

1.超聲波清洗機設備外殼帶電。

1. The shell of the ultrasonic cleaner is charged.

在這種情況下，多是由于電熱元件絕緣不良或其他元件電路連接不良。一般可以通過更換絕緣不良的元器件和接地線來解決。如果超聲波清洗機的外殼外有電，影響會很大，廠商一定要重視。如果發現超聲波清洗機帶電，先停機，再對故障進行初步判斷，由人員進行測試評估，確認解決方案。

In this case, it is mostly due to poor insulation of the heating element or poor connection of the circuit of other elements. Generally, it can be solved by replacing components and grounding wires with poor insulation. If there is electricity outside the shell of the ultrasonic cleaner, the impact will be great, and the manufacturer must pay attention to it. If it is found that the ultrasonic cleaner is charged, stop the machine first, and then make a preliminary judgment on the fault. Professional personnel will conduct test and evaluation to confirm the solution.

2.超聲波清洗機里沒有超聲波。

2. There is no ultrasonic in the ultrasonic cleaner.

如果在使用超聲波清洗機的過程中，突然沒有超聲波，說明設備沒有電加熱。要檢查電源，然后檢查溫控器設定的位置是否正常。確定非溫控器問題后，要檢查水位開關和電加熱器是否有故障。如果有相關部件或易損件工作不正常，應盡快更換故障部件。

If there is no ultrasonic wave in the process of using the ultrasonic cleaner, it means that the equipment is not electrically heated. First, check the power supply, and then check whether the set position of the temperature controller is normal. After determining the non temperature controller problem, check whether the water level switch and the electric heater have faults. If relevant components or wearing parts do not work normally, replace the faulty components as soon as possible.

3.超聲波清洗機的聲音不正常。

3. The sound of the ultrasonic cleaner is abnormal.

超聲波發生器或換能器的異常清洗效果下降。檢查傳感器引線兩個端子的絕緣電阻，拆下傳感器護罩，檢查是否有異常；還要看超聲波清洗機的聲音是否讓某些換能器無法適應缸體、水位、水溫的變化。改變水位，工件在進入或離開水面時不能移動太大。如果是夏天高溫超聲波清洗機發出很大的噪音，考慮是不是散熱問題。

Abnormal cleaning effect of ultrasonic generator or transducer is reduced. Check the insulation resistance of the two terminals of the sensor lead, remove the sensor shield and check whether there is any abnormality; It also depends on whether the sound of the ultrasonic cleaner makes some transducers unable to adapt to changes in the cylinder body, water level and water temperature. Change the water level, and the workpiece cannot move too much when entering or leaving the water surface. If the high-temperature ultrasonic cleaner makes a lot of noise in summer, consider whether it is a heat dissipation problem.

以上就是為大家介紹的有全自動超聲波清洗機的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://m.huayiav.cn

The above is a detailed introduction of the fully automatic ultrasonic cleaning machine. I hope it will be helpful to you. If you have any questions, please contact us. We will provide you with professional services http://m.huayiav.cn